题名

圓筒型附屬建物風載載重之探討

并列篇名

A Study on the Wind Loadings of the Cylindrical Tank on Buildings

DOI

10.6377/JA.200712.0010

作者

陳若華(Jwo-Hua Chen)

关键词

建築附屬設施 ; 風載重 ; 風洞實驗 ; Components ; Design Wind Loads ; Wind Tunnel Experiments

期刊名称

建築學報

卷期/出版年月

62_S期(2007 / 12 / 01)

页次

51 - 66

内容语文

繁體中文

中文摘要

台灣地區在歷次颱風中建築物之附屬構造物倒塌或毀損,皆威脅公共安全,有必要加以預防。本計畫透過蒐集國內外相關構造物之耐風設計方法、標準或規範,利用文獻整理與風洞試驗,以常見的建築物水塔等圓筒型附屬建物為例,建立參考之風壓或風力係數,供設計參考,檢討規範中關於圓筒型水塔,在不同底高的條件下,其設計風載重的表現。由研究結果顯示,對於不同筒底高度的水塔構造物而言,由規範中所建立的水平向風載重仍可涵蓋其適用範圍。本研究利用傾倒彎矩推算相當的模型頂等值靜載重,顯示提高圓筒高度,將迅速提高等值靜載重,實際設計時其對於基座桿件而言,傾倒彎矩的增加,包括基座桿件的抗拉拔及挫曲預防等均須加以特別考慮。此外採水平放置的圓筒,由於轉風攻角後並不對稱,其一般化外力係數均明顯提升。

英文摘要

There are lots of building components damaged by the extreme weather conditions, such as the typhoon, in Taiwan area every year. This situation will be a problem of safety of civilization lives. A suitable design criteria of wind loadings to these buildings is necessary for the designers and officers of buildings management. In this study couples of design codes and literatures are compared as the bases for the local provisions of design wind loads on buildings components and temple structures. Also a series of aerodynamics experiments about cylindrical tanks on buildings top were conducted to make up the necessary data. In experiments, the gap under the bottom of model and floor of wind tunnel was controlled as an important factor. The experimental results shown, that the gap will affect the wind force coefficients of models. But the design data provided by the code still can cover this variation. For the over turning moments of tank with different gap under the model were studied with the concept of equivalent loadings. The results shown, that the increasing of the gap under the tank will cause the equivalent loadings at the top of tank to be increased dramatically. This situation may cause the buckling of support columns under the tank and should be aware for the designer. The results also shown for the horizontal tank the change of attack angle of approaching flow, will change the project shape of tank into anti-symmetric. The generalized force of wind loadings will be increased.

主题分类 工程學 > 土木與建築工程
参考文献
  1. (1995).User`s Guide – NBC 1995 Structural Commentaries.Canada:
  2. (2004).AIJ Recommendations for Loads on Buildings, AIJ.Japan:
  3. (2000).Guide to the use of the wind load provisions of ASCE.USA:ASCE.
  4. (2000).Minimum Design Loads for Buildings and Other Structures.ANSI.
  5. (2002).Minimum Design Loads for Buildings and Other Structures.USA:ANSI.
  6. (1995).National Building Code of Canada 1995.Canada:
  7. (2002).AS/NZS.Australia:
  8. British Standard(1996).Loading for buildings-Part 2 : Code of pratice for wind loads.British Standards, UK..
  9. Lawson, T. V.(1997).Wind Loading Handbook-Guide to the use of BS 6399 Part 2.Butterworth Heinemann, UK..
  10. Robertson, A. P.,R. P. Hoxey, J. L. Short,W. A. Ferguson,P. A. Blackmore(1997).Wind loads on boundary walls: Full-scale studies.Journal of Wind Engineering and Industrial Aerodynamics,69-71,451-459.
  11. Tamura, Y.,Takeshi Ohkuma,Hisashi Okada,Jun Kanda(1999).Wind loading standards and design criteria in Japan.Journal of Wind Engineering and Industrial Aerodynamics,83(1-3),555-566.
  12. 內政部建築技術審議委員會、建築物耐風設計規範審查專案小組(2006)。建築物耐風設計規範及解說。台北:營建雜誌社。
  13. 陳若華、鄭啟明、吳重成(2004)。建築物風力設計規範之現況與比較。中華民國第七屆結構工程研討會,桃園:
  14. 劉中泰(2001)。台北,淡江大學土木工程研究所。
  15. 鄭啟明、吳重成、陳若華(2003)。內政部建築研究所專題研究計畫報告。台北:
  16. 鄭啟明、吳重成、陳若華(2002)。內政部建築研究所專題研究計畫報告。台北: