题名

殘餘應力與初始缺陷對壓力桿件臨界荷重影響之探討

并列篇名

The Investigation of the Critical Load of Compressive Member with Residual Stress & Initial Defects Influences

DOI

10.3966/101632122016060096001

作者

游新旺(Hsin-Wan Yu);張學誠(Hsueh-Cherng Chang);張鎮元(Cheng-Yuan Chang)

关键词

殘餘應力 ; 初始缺陷 ; 受壓桿件 ; 臨界荷重 ; Residual Stress ; Initial Defect ; Compressive Member ; Critical Load

期刊名称

建築學報

卷期/出版年月

96期(2016 / 06 / 30)

页次

1 - 14

内容语文

繁體中文

中文摘要

當桿件承受軸向壓力時,殘餘應力、桿件之初始彎曲和初偏心等瑕疵將對桿件整體穩定性產生影響。本研究首先探討殘餘應力、初始彎曲和初偏心分別對受壓桿件造成彎曲挫屈的失穩現象,研究中發覺,挫屈方向長細比相同時殘餘應力、初始彎曲或初偏心對斷面弱軸挫屈載重的影響較強軸大。本文將討論AISC規範的容許應力法(ASD)、荷載抗力係數設計法(LRFD)與中國大陸的GB規範等不同規範之臨界荷重和穩定係數,並將不同規範之計算結果與理論分析結果進行比較。另本研究在固定斷面高度改變斷面寬度下探討初始缺陷桿件臨界應力影響,研究中發現斷面寬度改變,對斷面弱軸臨界降伏應力比有些微影響,但對強軸臨界降伏應力比的影響則不顯著。最後,對於AISC規範,本研究提出桿件弱軸之長細比修正係數,以確保型鋼斷面弱軸與強軸之臨界荷重達到同一安全等級。

英文摘要

As the axial loading applied on the member, residual stress, initial crookedness and the initial eccentricity will affect the overall stability of the member. In the research, we investigated the residual stress, initial crookedness and initial eccentricity respectively for the instability phenomenon of bending buckling for compressive members. The study found that residual stress, initial crookedness and initial eccentricity affect the buckling load of weak axis more than strong axis at the same values of slenderness ratio. Then, we will discuss the critical load and stable coefficient of the different specifications such as AISC specification of the allowable stress method, the load and resistance factor design method and the GB specification of Mainland China. The calculation results and theoretical analysis of the specifications above will be compared. The different section widths with a fixed section height were also considered with these initial defects for critical loading of members. The normalized critical stresses of weak axis were affected by change of the section width factors, but the change was not significant for the normalized critical stresses of strong axis. Finally, the research proposed correction factor of slenderness ratio for weak axis design of steel sections. The results will be suggested to AISC Specification to ensure the same safety level of steel section on critical load calculation of strong & weak axis.

主题分类 工程學 > 土木與建築工程
参考文献
  1. AISC(2005).Manual of Steel Construction.IL, USA:American Institute of Steel Construction.
  2. AISC(1978).Specification for the Design, Fabrication and Erection of Structural Steel for Buildings.IL, USA:American Institute of Steel Construction.
  3. AISC(1986).Manual of Steel Construction- Load & Resistance Factor Design.IL, USA:American Institute of Steel Construction.
  4. Ang, A. H. S.,Tang, W. H.(1984).Probability Concepts in Engineering Planning and Design, Vol. 2- Decision, Risk, and Reliability.NY, USA:John Wiley & Sons.
  5. Beedle, L. S.,Tall, L.(1960).Residual stress and the compressive properties of steel- basic column strength.Proceedings of ASCE,VA, USA:
  6. Bjorhovde, R.(1972).PA, USA,Department of Civil Engineering, Lehigh University.
  7. Bjorhovde, R.(1978).The safety of steel columns.ASCE Journal of Structural Division,104(ST3),463-477.
  8. Chajes, A.(1974).Principles of Structural Stability Theory.NJ, USA:Prentice-Hall, Inc.
  9. Gere, J.,Timoshenko, S. P.(1990).Mechanics of Materials.MA, USA:PWS- Kent.
  10. Kreyszig, E.(2011).Advanced Engineering Mathematics.NJ, USA:John Wiley & Sons, Inc.
  11. Mathur, K.,Fahnestock, L. A.,Okazaki, T.,Parkolap, M. J.(2012).Impact of residual stresses and initial imperfections on the seismic response of steel moment frames.Journal of Structural Engineering,138(7),942-951.
  12. Mendenhall, W.,Beaver, R. J.,Beaver, B. M.(2006).Introduction to Probability and Statistics.CA, USA:Thomson Brooks/Cole.
  13. Nishino, F.,Tall, L.(1967).Residual Stress and the Local Buckling Strength of Steel Columns.PA, USA:Lehigh University.
  14. Yoo, C. H.,Lee, S. C.(2011).Stability of Structures -Principles and Applications.MA, USA:Butterworth-Heinemann.
  15. 中國計畫出版社(2003)。鋼結構設計規範─GB 50017。北京市=Beijing:中國計畫出版社=China Planning Press。
  16. 中華民國結構工程學會編、中國土木水利工程學會編、中華民國地震工程學會編、台灣省結構工程技師公會編、新北市結構工程技師公會編、國家地震工程研究中心編(2015)。鋼造建築耐震設計技術手冊。台北市=Taipei:科技圖書股份有限公司=Scientific & Technical Publishing Company, Ltd。
  17. 內政部營建署(2010)。鋼結構極限設計法規範及解說。台北市=Taipei:內政部營建署=Construction & Planning Agency Ministry of the Interior。
  18. 金文森、周綏平、段鍊、陳惠發(2008)。鋼結構設計。台北市=Taipei:科技圖書股份有限公司=Scientific & Technical Publishing Company, Ltd。
  19. 張學誠(1994)。台北市=Taipei,國立台灣科技大學營建工程系=Department of Civil & Construction Engineering, NTUST。
  20. 陳正誠、陳正平(2003)。鋼結構設計手冊─容許應力設計法。台北市=Taipei:科技圖書股份有限公司=Scientific & Technical Publishing Company, Ltd。
  21. 陳正誠、陳正平、林庚達、梁宇宸(2012)。鋼結構設計手冊─極限設計法。台北市=Taipei:中華民國鋼結構協會=Taiwan Institute of Steel Construction。
  22. 陳生金(2003)。鋼結構設計─極限設計法與容許應力法。台北市=Taipei:科技圖書股份有限公司=Scientific & Technical Publishing Company, Ltd。
  23. 陳生金、陳希舜、曾清銓(1992)。鋼結構極限設計法規範及解說研究。台北市=Taipei:中華民國結構工程學會=Chinese Society of Structural Engineering。
  24. 陳紹蕃、顧強(2014)。鋼結構。北京市=Beijin:中國建築工業出版社=China Architecture & Building Press。
  25. 陳惠發、周綏平、陸楸、吳惠弼、金文森(1994)。樑柱分析與設計─第一部。台北市=Taipei:科技圖書股份有限公司=Scientific & Technical Publishing Company, Ltd.。
  26. 陳惠發、周綏平、陸楸、吳惠弼、金文森(1994)。樑柱分析與設計─第一部。台北市=Taipei:科技圖書股份有限公司=Scientific & Technical Publishing Company, Ltd.。